OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
So I decided to put a BV500 engine in a lambretta. I received a lot of discouragement, telling me how bad the idea was, so I decided I had to do it.

People kept telling me that it had been done once and that it was a disaster. I then found the bike they were talking about and though: "really?". It had to be possible to do a better job than this....

External inline image provided by member with no explanatory text

So I started with what I thought was one of the biggest problems... The front wheel.

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

Next I sent the wheel to Rocky's wheel works and had it re-trued and once back, powder coated.

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text


Next started working on splicing forks into frame with new bearing cups and shortening fork tubes two inches.

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

Chop chop on frame, using stock BV motor mount.

External inline image provided by member with no explanatory text


Frame tubes bent and start to mock up

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

Shorten forks, to get rid of the "chopper" look
External inline image provided by member with no explanatory text

Original springs vs. new springs for two inch reduction in height.

External inline image provided by member with no explanatory text

New height with body first mock ups

External inline image provided by member with no explanatory text

widening starts.

External inline image provided by member with no explanatory text

And that brings us up to date.

Next I will be finalizing the installation of the bv bearing cups and front end connections. This will allow me to finalize connections of front frame to rear frame.
@turkman avatar
UTC

Ossessionato
2009 GTV 250
Joined: UTC
Posts: 2533
Location: Olympia, WA
 
Ossessionato
@turkman avatar
2009 GTV 250
Joined: UTC
Posts: 2533
Location: Olympia, WA
UTC quote
Going to be very interesting!!!
@joshzingzing avatar
UTC

Veni, Vidi, Posti
px200 cutdown,px180,px150. Puch SR. Puch scooterette
Joined: UTC
Posts: 5109
Location: west aus
 
Veni, Vidi, Posti
@joshzingzing avatar
px200 cutdown,px180,px150. Puch SR. Puch scooterette
Joined: UTC
Posts: 5109
Location: west aus
UTC quote
putting in the effort




could make a nice tourer , should fairly float eh
@bigben avatar
UTC

Evil
p2, jet2, lml166
Joined: UTC
Posts: 666
Location: Philadelphia, United States
 
Evil
@bigben avatar
p2, jet2, lml166
Joined: UTC
Posts: 666
Location: Philadelphia, United States
UTC quote
what forks are you running? stock bv?
piaggio typhoon forks fit pretty well under a stock horncast if the edges are grinded down a little. j/s

great project though.
@gogogordy avatar
UTC

Veni, Vidi, Posti
Reprehensible Misinformant
Joined: UTC
Posts: 7573
Location: Winchester, California
 
Veni, Vidi, Posti
@gogogordy avatar
Reprehensible Misinformant
Joined: UTC
Posts: 7573
Location: Winchester, California
UTC quote
Thats gonna be quite a marriage!
Well done.

And those that say "it can't be done" really mean they couldn't do it!

Cant wait to see the finished product....should be quite a goer.
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
bigben wrote:
what forks are you running? stock bv?
piaggio typhoon forks fit pretty well under a stock horncast if the edges are grinded down a little. j/s

great project though.
I went with the stock BV forks, as they interface nicely with the bv hub and disks. Didn't want to get into modifying all of that.

Also wanted the FU factor of having dual front disks.

All I had to do is change the springs for shorter stiffer ones, to shorten the forks. Wasn't happy about widening the front fender at first, but proportionally, it works better with the wider rear end.

One problem I am having now is that i need the metering module, where all the brake lines intersect. Not easy to find.
UTC

Enthusiast
LI's and a Jet
Joined: UTC
Posts: 76
Location: Petaluma, CA
 
Enthusiast
LI's and a Jet
Joined: UTC
Posts: 76
Location: Petaluma, CA
UTC quote
Glad those panels are out of my garage! Kick ass project too.
@koenig_blues avatar
UTC

Veni, Vidi, Posti
a not so normal vbb2 '64, a weirdo vbx '86, a not so normal pts100 '82 and a yellow sunshine '74 sprint
Joined: UTC
Posts: 5802
Location: Indo
 
Veni, Vidi, Posti
@koenig_blues avatar
a not so normal vbb2 '64, a weirdo vbx '86, a not so normal pts100 '82 and a yellow sunshine '74 sprint
Joined: UTC
Posts: 5802
Location: Indo
UTC quote
cool project mate
@qascooter avatar
UTC

Ossessionato
79 P200E (Ruby), 62 Allstate (B-62)
Joined: UTC
Posts: 4167
Location: Florence, OR
 
Ossessionato
@qascooter avatar
79 P200E (Ruby), 62 Allstate (B-62)
Joined: UTC
Posts: 4167
Location: Florence, OR
UTC quote
Well this is very exciting to watch go together. Thanks for taking the pics and showing us what's what as you're doing it. Very cool!
@bigben avatar
UTC

Evil
p2, jet2, lml166
Joined: UTC
Posts: 666
Location: Philadelphia, United States
 
Evil
@bigben avatar
p2, jet2, lml166
Joined: UTC
Posts: 666
Location: Philadelphia, United States
UTC quote
great project, i'll watch intently. its also nice to see more vintage auto projects stateside. if you're not on the series six forum i'd advise it.

what's your intent with accomodating the engine lengthwise? widening the frame past around the tail light/behind the panels or fabricating a huge bridge piece to cover the cylinder?
@quaddiekev avatar
UTC

Enthusiast
Joined: UTC
Posts: 80
Location: uk
 
Enthusiast
@quaddiekev avatar
Joined: UTC
Posts: 80
Location: uk
UTC quote
lambretta projects
If you like this conversion have a look at some of the the completed projects on here http://www.lambrettainnovation.co.uk
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
quaddiekev I am pretty aquatinted with that site.

bigben what is the series six forum. is it the 300 piaggio engine in the lambretta frame??

Regarding putting the engine lengthwise... I did that to keep the gas tank and air box under the bodywork. I will sink the cylinder head into the floorboards and create a cover for the head. I am trying to minimize the presence of the head, where your feet are. Shouldn't be too much.

Derek m Thanks for the great deal on those panels. I won't hack them up....

here are the latest pictures. I am working on widening the front fender. I also lowered the top frame plate, which was drilled off of the body. I will be creating a "can" consisting of the side covers and center body. This will be on a pivot, like a car hood.

External inline image provided by member with no explanatory text


External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

External inline image provided by member with no explanatory text

Ride height set at 29.5"

External inline image provided by member with no explanatory text
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
did a bunch of filling on the body can today. Actually got more done than pictured.

I also modified the frame back to create a resting point for the body can. it will make sense when you see the final.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
@bigben avatar
UTC

Evil
p2, jet2, lml166
Joined: UTC
Posts: 666
Location: Philadelphia, United States
 
Evil
@bigben avatar
p2, jet2, lml166
Joined: UTC
Posts: 666
Location: Philadelphia, United States
UTC quote
yes and no. the series six forum is an extension of lambrettainnovations site which in turn makes the scomadi TL 250/300 that you're talking about

http://www.hostingphpbb.com/forum/index.php?mforum=seriessix

but its generally not available through the main gateway, i tend to sneak in through the sub forums

http://www.hostingphpbb.com/forum/viewforum.php?f=10&mforum=seriessix

a huge bridge piece looked like the smartest way to go. if you're great with welding, i may start up a convo with you as i'll likely look to get a customized glovebox setup for my own project, a gts250 engine in a lambretta frame
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
quick update
doing an update on the forks graft.

Ended up deciding to weld in the cups, vs. brazing and spot welding the tubes. I did this becuase I noticed the connection being a little compromised and didn't want to take any chances.

I did the bottom welding and part of the top tacking, with the forks in place, but i am getting some slight binding in the last 10 degrees of rotation to the right. Frankly it probably wouldn't make much difference, but I might try a little copper hammer on the top cup, to shift it ever so slightly.

Really starting to try and consider how to jig for the connection to the rear.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
@mingas avatar
UTC

Member
Vespa PX125E - Vespa T5
Joined: UTC
Posts: 18
Location: Lisbon - Portugal
 
Member
@mingas avatar
Vespa PX125E - Vespa T5
Joined: UTC
Posts: 18
Location: Lisbon - Portugal
UTC quote
Great Project.

Continued.

Cumps.
@bigben avatar
UTC

Evil
p2, jet2, lml166
Joined: UTC
Posts: 666
Location: Philadelphia, United States
 
Evil
@bigben avatar
p2, jet2, lml166
Joined: UTC
Posts: 666
Location: Philadelphia, United States
UTC quote
please tell me you're using a lammy headset and not BV handlebars.

looks good though, a bit wide for my tastes but innovative nonetheless. beats another restoration thread anyday.
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
bigben wrote:
please tell me you're using a lammy headset and not BV handlebars.

looks good though, a bit wide for my tastes but innovative nonetheless. beats another restoration thread anyday.
The only part of those handle bars I'm using is the neck clamp. I will be drilling out the lambretta tubes and replacing them with new 7/8" tubes, which will connect with the BV bars neck clamp. Just connecting these bars to move the front wheel temporarily.

Did some more work today... Front meets back. These pictures are getting close to final positioning of body. As you can see, you won't have much head to deal with, or much extension to the back.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
little bit of metal finishing moving forward. I must say that I am pretty rusty.

No pun intended.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
@t5bitza69 avatar
UTC

Veni, Vidi, Posti
T5s
Joined: UTC
Posts: 17005
Location: The West Of Yorkshire ... Gods Country
 
Veni, Vidi, Posti
@t5bitza69 avatar
T5s
Joined: UTC
Posts: 17005
Location: The West Of Yorkshire ... Gods Country
UTC quote
quality
them bars look vega-ish
@dr_zoidberg avatar
UTC

Ossessionato
Ducati Scrambler 800 Nightshift
Joined: UTC
Posts: 3418
Location: Bromsgrove, UK
 
Ossessionato
@dr_zoidberg avatar
Ducati Scrambler 800 Nightshift
Joined: UTC
Posts: 3418
Location: Bromsgrove, UK
UTC quote
Looking good!
@trumpyscooter avatar
UTC

Molto Verboso
Black 2007 PX200, Dark green 1986 PX225 Pinasco, "1972"(yeah rite) Tangerine px200, several TRIUMPH TIGRESS SCOOTERS
Joined: UTC
Posts: 1082
Location: New Zealand
 
Molto Verboso
@trumpyscooter avatar
Black 2007 PX200, Dark green 1986 PX225 Pinasco, "1972"(yeah rite) Tangerine px200, several TRIUMPH TIGRESS SCOOTERS
Joined: UTC
Posts: 1082
Location: New Zealand
UTC quote
Man, you are a BOSS!

Awesome project thats gonna set the standards man.

kia kaha!
@bigben avatar
UTC

Evil
p2, jet2, lml166
Joined: UTC
Posts: 666
Location: Philadelphia, United States
 
Evil
@bigben avatar
p2, jet2, lml166
Joined: UTC
Posts: 666
Location: Philadelphia, United States
UTC quote
pm'ed you btw
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
update
Let me start by saying Geometry sucks. It has taken a week of screwing around to finally come up with a configuration that will allow the shocks and engine to travel.

So photoshop modeling wasn't working out and I tried the Disney method.

Then I finally, with the help of a more skilled frame builder, established the method of deciding where to mock the frame for weld. That is the median point of shock travel. With that I welded on a mock wire for shock end position. Now I could rotate the frame can and establish clearance.

Once i have moved the frame components about 300 times, I found the sweet spot.

With that I was able to do some initial tacking. Now I take this first part of the assembly to a real welder to have it straightened and welded.
Next I will do the nominal mock up for connecting the front to the rear.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Nominal riding position
Nominal riding position
Maximum shock compression.
Maximum shock compression.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
This obviously isn't how the bike will be connected.  The rear is still independent and this is showing maximum shock compression.
This obviously isn't how the bike will be connected. The rear is still independent and this is showing maximum shock compression.
@bommes avatar
UTC

Hooked
GTS 250 a.b.s.
Joined: UTC
Posts: 483
Location: Noord Brabant, Netherlands
 
Hooked
@bommes avatar
GTS 250 a.b.s.
Joined: UTC
Posts: 483
Location: Noord Brabant, Netherlands
UTC quote
I wish I had a workshop like that this build rocks my socks off..!!!

Oh and one other thing..:
That front-brake.. hahha that will sure stop this bike, the disk looks massive on that small wheel.
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
Bommes wrote:
I wish I had a workshop like that this build rocks my socks off..!!!

Oh and one other thing..:
That front-brake.. hahha that will sure stop this bike, the disk looks massive on that small wheel.
Funny you should say that, about the brakes, I am a little concerned. Might be a little too much stopping power. I just couldn't resist the dual 10 inch disks.

Small update: Shot a laser across the rear wheel today, for reference, and now the first part of the frame goes in for welding tomorrow. With this first section welded, I can connect the rest and weld the side covers on.
@gogogordy avatar
UTC

Veni, Vidi, Posti
Reprehensible Misinformant
Joined: UTC
Posts: 7573
Location: Winchester, California
 
Veni, Vidi, Posti
@gogogordy avatar
Reprehensible Misinformant
Joined: UTC
Posts: 7573
Location: Winchester, California
UTC quote
BVbretta
One of the most intriguing projects ever!
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
quick update. have established extension length and patching in filler. Looks a little messy, but should grind up nice.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
@joshzingzing avatar
UTC

Veni, Vidi, Posti
px200 cutdown,px180,px150. Puch SR. Puch scooterette
Joined: UTC
Posts: 5109
Location: west aus
 
Veni, Vidi, Posti
@joshzingzing avatar
px200 cutdown,px180,px150. Puch SR. Puch scooterette
Joined: UTC
Posts: 5109
Location: west aus
UTC quote
blackboard
.duster
⚠️ Last edited by joshzingzing on UTC; edited 1 time
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
update.

Dropped first part of frame to be welded. When I went to check, everything crooked, so I spent a couple hours giving the welder a crash course in how to make something straight.

I put the first section in and it was still a bit twisted, so I had to heat the main tube and rotate it a couple of degrees.

I discovered that BV500 rear shocks are offset, so I had to weld up the left bracket and relocate the hole so that the shocks line up.

Next step is to install the shock mount on the rear, then set it with a temporary spacer, to allow for the frame to finally be connected. I have laid in the tube and it looks good.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
shocks finally getting connected to frame
Forum member supplied image with no explanatory text
@coldbeer avatar
UTC

Hooked
PX200Arcobaleno, Granturismo200L
Joined: UTC
Posts: 155
Location: Croatia, Europe
 
Hooked
@coldbeer avatar
PX200Arcobaleno, Granturismo200L
Joined: UTC
Posts: 155
Location: Croatia, Europe
UTC quote
Following this one
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
finnaly arrived at the connection length. The only issue is that the engine mounting bolt is 2/3rd covered. Will work it out.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
@vulcan_scooter_secte avatar
UTC

Member
PX200 / PX210 / GP125 / RALLY200
Joined: UTC
Posts: 41
Location: PARIS / FRANCE
 
Member
@vulcan_scooter_secte avatar
PX200 / PX210 / GP125 / RALLY200
Joined: UTC
Posts: 41
Location: PARIS / FRANCE
UTC quote
It's going to be a rocking Bretta !
@vader19 avatar
UTC

Mr. Clean
P,SUPER,V90, 50 Special
Joined: UTC
Posts: 10205
Location: This is't my locker!
 
Mr. Clean
@vader19 avatar
P,SUPER,V90, 50 Special
Joined: UTC
Posts: 10205
Location: This is't my locker!
UTC quote
I'm lovin' it.. the front wheel/disc brake setup you did is killer! Very cool
UTC

Addicted
GTS250
Joined: UTC
Posts: 507
Location: Trowbridge - England
 
Addicted
GTS250
Joined: UTC
Posts: 507
Location: Trowbridge - England
UTC quote
brilliant, amazing work.
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
struggling with multiple issues. wheel alignment, frame rail twists..... Damn it.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
We are officially on wheels
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
OP
UTC

Enthusiast
Joined: UTC
Posts: 50
 
Enthusiast
Joined: UTC
Posts: 50
UTC quote
after about 100 hours of online research, I have arrived at how I am going to address the hydraulics.

Originally I was going to get remote reservoir levers and put the reservoirs inside the headset. The only financially viable options were in china and I wasn't confident about that.

External inline image provided by member with no explanatory text

So I decided go go with a cable activated Remote master cylinder.

Next I looked at remote master cylinders, like the Grimeca. The problem is that the stock bv has a 12mm piston master cylinder and the Grimeca is 11mm:

External inline image provided by member with no explanatory text

Next I looked at Karting cylinders, which have bigger pistons, but they are very large and can only be mounted in horizontal direction:

External inline image provided by member with no explanatory text

I finally stumbled across this. It is 12.7mm (larger), American, and the price is right.

External inline image provided by member with no explanatory text

SO!!!!!!! If anyone has the stock levers, shifter sleeve, and throttle for a GP headset. PLEASE hook me up!! Also need the headlight and ring.
UTC

Molto Verboso
07 LX50
Joined: UTC
Posts: 1977
 
Molto Verboso
07 LX50
Joined: UTC
Posts: 1977
UTC quote
What a job! Hey try here .

http://www.scootersoriginali.com/
DoubleGood Design banner

Modern Vespa is the premier site for modern Vespa and Piaggio scooters. Vespa GTS300, GTS250, GTV, GT200, LX150, LXS, ET4, ET2, MP3, Fuoco, Elettrica and more.

Buy Me A Coffee
 

Shop on Amazon with Modern Vespa

Modern Vespa is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com


All Content Copyright 2005-2024 by Modern Vespa.
All Rights Reserved.


[ Time: 0.1647s ][ Queries: 45 (0.1243s) ][ Debug on ][ 313 ][ Thing One ]