OP
@mitsouni avatar
UTC

Hooked
px 200 disc brake cutdown
Joined: UTC
Posts: 149
Location: chania crete greece
 
Hooked
@mitsouni avatar
px 200 disc brake cutdown
Joined: UTC
Posts: 149
Location: chania crete greece
UTC quote
hi again.i hope this question is easier than the others which i got no responce!!i will put the malosi sport on in a few months,and i want to install a reed valve.any suggestions?i was going to use this one for 28 carb that i alredy have,with bgm reed.is the 28 carb powerfull enough for the sport cylinder with reeds?.any other set ups that already work good?cheers!!
https://www.scooter-and-service.de/custom-parts/motorteile/874/membrankit-konfigurator-px?c=149
@sara_alexandra avatar
UTC

Hooked
PX232 Lambretta li s3, Vespa cross, Vespa cross prototype, Honda NS400r....
Joined: UTC
Posts: 282
Location: Belgium
 
Hooked
@sara_alexandra avatar
PX232 Lambretta li s3, Vespa cross, Vespa cross prototype, Honda NS400r....
Joined: UTC
Posts: 282
Location: Belgium
UTC quote
will work with the 28mm carb, beter with a 30mm flatslide or pwk.
Reedvalve of a RD350 is very good. Steel petals? change them for fibre ones. Some spare money? Buy a Tassinari VForce3 with a spacer of 30mm.
@vader19 avatar
UTC

Mr. Clean
P,SUPER,V90, 50 Special
Joined: UTC
Posts: 10205
Location: This is't my locker!
 
Mr. Clean
@vader19 avatar
P,SUPER,V90, 50 Special
Joined: UTC
Posts: 10205
Location: This is't my locker!
UTC quote
I have one of those S&S blocks.. works great.. so does the MRP... I'd get the MRP.. less stuff to mess with.

Yes a 28mm carb will be enough
for the sport 210 cylinder..
@sara_alexandra avatar
UTC

Hooked
PX232 Lambretta li s3, Vespa cross, Vespa cross prototype, Honda NS400r....
Joined: UTC
Posts: 282
Location: Belgium
 
Hooked
@sara_alexandra avatar
PX232 Lambretta li s3, Vespa cross, Vespa cross prototype, Honda NS400r....
Joined: UTC
Posts: 282
Location: Belgium
UTC quote
Vader19 wrote:
I have one of those S&S blocks.. works great.. so does the MRP... I'd get the MRP.. less stuff to mess with.

Yes a 28mm carb will be enough
for the sport 210 cylinder..
i have the MRP, made some extra connections to mount a fuel pump (vacuum)
OP
@mitsouni avatar
UTC

Hooked
px 200 disc brake cutdown
Joined: UTC
Posts: 149
Location: chania crete greece
 
Hooked
@mitsouni avatar
px 200 disc brake cutdown
Joined: UTC
Posts: 149
Location: chania crete greece
UTC quote
do you really need a fuel pump?does the carb get higher than a no reed valve carb?fuel pumps are put on only if the petrol dont come all from the tank to the carb...with my 28 carb,it uses' all the petrol down to the very last drop !!!
@vader19 avatar
UTC

Mr. Clean
P,SUPER,V90, 50 Special
Joined: UTC
Posts: 10205
Location: This is't my locker!
 
Mr. Clean
@vader19 avatar
P,SUPER,V90, 50 Special
Joined: UTC
Posts: 10205
Location: This is't my locker!
UTC quote
mitsouni wrote:
do you really need a fuel pump?!
NO! I run 35mm carbs that suck gas like crazy and with a good fuel tap like the BGM (best one) you don't need a pump!
OP
@mitsouni avatar
UTC

Hooked
px 200 disc brake cutdown
Joined: UTC
Posts: 149
Location: chania crete greece
 
Hooked
@mitsouni avatar
px 200 disc brake cutdown
Joined: UTC
Posts: 149
Location: chania crete greece
UTC quote
there are 2 MRP manifolds,one with short and one with long intake sealings.what that means?i suppose the 30 mm one is for 28 carb,as they say in the description..
@sara_alexandra avatar
UTC

Hooked
PX232 Lambretta li s3, Vespa cross, Vespa cross prototype, Honda NS400r....
Joined: UTC
Posts: 282
Location: Belgium
 
Hooked
@sara_alexandra avatar
PX232 Lambretta li s3, Vespa cross, Vespa cross prototype, Honda NS400r....
Joined: UTC
Posts: 282
Location: Belgium
UTC quote
Measured today the difference between the bottom of the tank and the float bowl of the carb. Its almost the same, will wait with the fuel pump, and make some runs first.
Sara
OP
@mitsouni avatar
UTC

Hooked
px 200 disc brake cutdown
Joined: UTC
Posts: 149
Location: chania crete greece
 
Hooked
@mitsouni avatar
px 200 disc brake cutdown
Joined: UTC
Posts: 149
Location: chania crete greece
UTC quote
anyone tried or know someone who tried the [redacted] atomic mini reed valve that dont need to cut your cases?im not looking for a super tuned vespa!
@ginch avatar
UTC

Veni, Vidi, Posti
74 Super, 75 Super, PX project, LML off-roader and '66 Blue Badge Smallframe
Joined: UTC
Posts: 8889
Location: Victoria, Australia
 
Veni, Vidi, Posti
@ginch avatar
74 Super, 75 Super, PX project, LML off-roader and '66 Blue Badge Smallframe
Joined: UTC
Posts: 8889
Location: Victoria, Australia
UTC quote
It looks like good design but the openable area of the reed is going to be tiny compared to the RD350 type. Still, you could use it for a year and sell it on when you get the big one.
DoubleGood Design banner

Modern Vespa is the premier site for modern Vespa and Piaggio scooters. Vespa GTS300, GTS250, GTV, GT200, LX150, LXS, ET4, ET2, MP3, Fuoco, Elettrica and more.

Buy Me A Coffee
 

Shop on Amazon with Modern Vespa

Modern Vespa is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com


All Content Copyright 2005-2025 by Modern Vespa.
All Rights Reserved.


[ Time: 0.0130s ][ Queries: 3 (0.0032s) ][ live ][ 325 ][ ThingOne ]