OP
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
charlieman22 wrote:
That is certainly a quality plate.
It's gonna need some rubber of course…
I've had some luck just pinching some thin rubber between the carb box and motor.
It's definitely not as elegant.
Also doesn't test for carb box leak - so urs is better.
I think i have some thin adhesive backed rubber sheeting somewhere on a shelf, so my plan was to use that...if i can find it.
@charlieman22 avatar
UTC

Nedminder
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
 
Nedminder
@charlieman22 avatar
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
UTC quote
You have great shelves.

I used that line all through college - and I always meant it.
@ray8 avatar
UTC

Ossessionato
Joined: UTC
Posts: 2429
Location: Los Angeles
 
Ossessionato
@ray8 avatar
Joined: UTC
Posts: 2429
Location: Los Angeles
UTC quote
whodatschrome wrote:
Yes, AC120/BE4 is T5 jetting. So how is the AC140/BE3 different?
The 120 vs 140/150/160 ac initiates the main circuit too early.
Horrible on a stop and go bike.

The BE4 is an odd creature.
Super rich as the circuit initiates, since the only holes on that bastard are below the fuel line.
Lean at highest revs, once air from the ac reaches the lower holes and impedes/emulsifies fuel flow through the well.
@108 avatar
UTC

Ossessionato
V range 50s
Joined: UTC
Posts: 2427
 
Ossessionato
@108 avatar
V range 50s
Joined: UTC
Posts: 2427
UTC quote
Ray8 wrote:
The 120 vs 140/150/160 ac initiates the main circuit too early.
Horrible on a stop and go bike.

The BE4 is an odd creature.
Super rich as the circuit initiates, since the only holes on that bastard are below the fuel line.
Lean at highest revs, once air from the ac reaches the lower holes and impedes/emulsifies fuel flow through the well.
Great words of wisdom why you should relook at using a 120.

I've never seen anyone make it work on a tuned engine.
@charlieman22 avatar
UTC

Nedminder
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
 
Nedminder
@charlieman22 avatar
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
UTC quote
Tho I hesitate to have this conversation in front of the patient - a man known to abhor jetting largely because there are so many angles/opinions - I have to ask:

Are T5s un rideable in the city?
I've never heard that.

All my tuned engines, that utilized an SI 2424 carb, we're jetted with the 120 air corrector. I thought they were pretty superbly running motors.

Surprised that you guys think differently.
@ginch avatar
UTC

Veni, Vidi, Posti
74 Super, 75 Super, PX project, LML off-roader and '66 Blue Badge Smallframe
Joined: UTC
Posts: 10443
Location: Ballarat VIC, Australia
 
Veni, Vidi, Posti
@ginch avatar
74 Super, 75 Super, PX project, LML off-roader and '66 Blue Badge Smallframe
Joined: UTC
Posts: 10443
Location: Ballarat VIC, Australia
UTC quote
charlieman22 wrote:
Tho I hesitate to have this conversation in front of the patient - a man known to abhor jetting largely because there are so many angles/opinions - I have to ask:

Are T5s un rideable in the city?
I've never heard that.

All my tuned engines, that utilized an SI 2424 carb, we're jetted with the 120 air corrector. I thought they were pretty superbly running motors.

Surprised that you guys think differently.
Didn't you used to have something Jack wrote in your sig line about the 120? Something about being the "nuts for wide open throttle abuse".
@qascooter avatar
UTC

Veni, Vidi, Posti
79 P200E (Ruby), 62 Allstate (B-62), 63 VBB (Storm)
Joined: UTC
Posts: 5325
Location: Florence, OR
 
Veni, Vidi, Posti
@qascooter avatar
79 P200E (Ruby), 62 Allstate (B-62), 63 VBB (Storm)
Joined: UTC
Posts: 5325
Location: Florence, OR
UTC quote
charlieman22 wrote:
Surprised that you guys think differently.
I am surprised also. I've got one engine (177 pinasco 2 port) with a 24/24 and a 120/be4 combo and it does great around town or WOT. Its probably a bit rich down low, but it runs great and doesn't stutter.

And with the 208 with 60mm crank (like Whodats) Im currently working on tuning, I've got a 100AC and BE4 and it's running great, but I haven't checked WOT heat issues. The PSI is 177 though, which could be part of the problem, or the timing, which is 18 degrees currently. Maybe it needs to be more like 21 degrees.

Anyway, I'm curious also... Hmmmm....
OP
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
Ummm...guys, i'm right here. Reminds me a couple years ago when my surgeons were having a similar conversation on how to reassemble my foot. I didn't understand a word they said back then either. I probably should have since they seized up my metatarsals with plates and screws. I kinda hated life for the next full year after that.
@charlieman22 avatar
UTC

Nedminder
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
 
Nedminder
@charlieman22 avatar
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
UTC quote
The patient should drill his carb.
Check for air tightness.
The rest is a matter of subtleties.
🙂
OP
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
charlieman22 wrote:
The patient should drill his carb.
Check for air tightness.
The rest is a matter of subtleties.
🙂
I got two different drill bit sizes to choose from 2.18mm or 2.37mm. Which one would be best? Keep in mind that it's just a warmed over 208 and not a built molassi 210.
OP
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
Ray8 wrote:
Get this and this:
https://www.amazon.com/gp/product/B000RWB03W/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

https://www.amazon.com/gp/product/B08SC447W6/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1

I have a spare blanking plate that goes in the airbox if you want to try it.
IIRC a 1 1/2" bilge plug should fit the exhaust stub.
Thank you again for the parts list! I assembled everything together this evening. So how long do i need to pressure test it for? 2 minutes?...20 minutes?...2 hours?...overnight? And how many HG do i pump up the bulb?
Forum member supplied image with no explanatory text
@qascooter avatar
UTC

Veni, Vidi, Posti
79 P200E (Ruby), 62 Allstate (B-62), 63 VBB (Storm)
Joined: UTC
Posts: 5325
Location: Florence, OR
 
Veni, Vidi, Posti
@qascooter avatar
79 P200E (Ruby), 62 Allstate (B-62), 63 VBB (Storm)
Joined: UTC
Posts: 5325
Location: Florence, OR
UTC quote
I'd pump it up to 250 and use the 2.37mm drill bit

EDIT: 250 for 5 minutes
@charlieman22 avatar
UTC

Nedminder
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
 
Nedminder
@charlieman22 avatar
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
UTC quote
I use 260HG and 5 min.
You will either be air tight or not.

As for carb.
Either bit.
The smaller will give u 2.2 which should be enough - but there little harm in being closer to 2.4.
This passage should not be involved in the flow restriction of fuel - that's the jets job.


Just clean out that passage really well after drilling. Flush it - not just with air. Ask me how I know…
OP
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
charlieman22 wrote:
I use 260HG and 5 min.
You will either be air tight or not.

As for carb.
Either bit.
The smaller will give u 2.2 which should be enough - but there little harm in being closer to 2.4.
This passage should not be involved in the flow restriction of fuel - that's the jets job.


Just clean out that passage really well after drilling. Flush it - not just with air. Ask me how I know…
I pumped the gauge to 260mmgh. I'm loosing about 2mmGH every 5 minutes so obviously there's a leak somewhere. I got out the soapy water and gave everything a spritz. I don't see any bubbles just yet. I have not removed the clutch and its cover to get a look at that seal. I was just thinking, but for that can i just check to see if any air is coming out of the crankcase breather instead? Or what is the chances that my $15 scamazon blood pressure kit has some sort of internal leak?
@az_slynch avatar
UTC

Ossessionato
'07 GTS250, '07 LX150, '81 P200E, '78 P200E, '74 VBC1, '64 V90 and 3 Ciaos
Joined: UTC
Posts: 2157
Location: Tucson, AZ
 
Ossessionato
@az_slynch avatar
'07 GTS250, '07 LX150, '81 P200E, '78 P200E, '74 VBC1, '64 V90 and 3 Ciaos
Joined: UTC
Posts: 2157
Location: Tucson, AZ
UTC quote
If soapy water isn't telling any tales, maybe it's some to MacGuyver up a smoke tester?
@sdjohn avatar
UTC

Johnny Two Tone
'15 GTS300, '86 PX125EFL, '01 ET4
Joined: UTC
Posts: 9072
Location: San Diego, CA
 
Johnny Two Tone
@sdjohn avatar
'15 GTS300, '86 PX125EFL, '01 ET4
Joined: UTC
Posts: 9072
Location: San Diego, CA
UTC quote
Most common leak sites - your plugs at the exhaust or intake….

Soapy water spray is a good way to look
@charlieman22 avatar
UTC

Nedminder
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
 
Nedminder
@charlieman22 avatar
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
UTC quote
Ok.
Here are my best tricks.
Note: borrowed and inspired by many.
Finding leaks:
1. Gravity is ur friend. The best soapy water test is pooled soapy water. Example: set motor on its side so clutch side pointed to the sky. Fire soapy water on seal. If it's leaking - u will be the star of your nephews birthday party with ur bubble animals.
2. This means u have to have the cylinder both pointing to the sky, and hanging straight down. Apply that to everything. If u feel like u r trying to spray a tough spot to keep liquid on, flip the motor so it's holding soapy water.

Ur gonna find it - and when u do - it's gonna feel great when eradicated.

Wild guess: pin hole in Welded head?
Use gravity. Flood it. If not - Check it off the list and celebrate. U have the dreaded small leak - some spot is gonna blow bubbles
OP
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
charlieman22 wrote:
Ok.
Here are my best tricks.
Note: borrowed and inspired by many.
Finding leaks:
1. Gravity is ur friend. The best soapy water test is pooled soapy water. Example: set motor on its side so clutch side pointed to the sky. Fire soapy water on seal. If it's leaking - u will be the star of your nephews birthday party with ur bubble animals.
2. This means u have to have the cylinder both pointing to the sky, and hanging straight down. Apply that to everything. If u feel like u r trying to spray a tough spot to keep liquid on, flip the motor so it's holding soapy water.

Ur gonna find it - and when u do - it's gonna feel great when eradicated.

Wild guess: pin hole in Welded head?
Use gravity. Flood it. If not - Check it off the list and celebrate. U have the dreaded small leak - some spot is gonna blow bubbles
I had no idea that finding this small of an air leak would be this big of a deal. Still no luck in finding it yet. I'm not really excited about the thought of pulling the engine just to rotate it around in circles (in order to pool the soapy water). Yeah, it's only takes like 5~10 minutes to pull the engine, but it just seems like i'm going backwards.

I too also suspected that the welded head could be a possible culprit, but it was bubble free. I'm wondering if the air leak is simply between the airbox and the case?

I also looked at Plan B this evening as well. I have another all stock P200 engine on my shelf. I was just going to yank out the 208 engine and toss it on the shelf for a few years (or so) and swap in the other 200 in its place. But i pressure tested it first and found an air leak in the clutch side crank seal...so i spend about 20 minutes tearing down that engine to make a parts list. The loose gears are in excellent shape, but the cross is worn. I'll also replace the fly side bearing and seal. It could also use a new pair of piston rings (it's a GS 200 66.9mm piston). My plan is to order up those parts asap. In the meantime i'll keep searching for the leak in the 208. If i don't find it by the time my 200 parts arrive, then in goes an all stock (flowed) 200. No, not as powerful as a 208, but a 200 can still go 65~70mph.
UTC

Jet Eye Master
PX221 MHR heavily tuned, PX200 O tuned, PX181 M1XL tuned, PX166 tuned a quite bit and some motorbikes
Joined: UTC
Posts: 5491
Location: London UK
 
Jet Eye Master
PX221 MHR heavily tuned, PX200 O tuned, PX181 M1XL tuned, PX166 tuned a quite bit and some motorbikes
Joined: UTC
Posts: 5491
Location: London UK
UTC quote
whodatschrome wrote:
I pumped the gauge to 260mmgh. I'm loosing about 2mmGH every 5 minutes so obviously there's a leak somewhere. I got out the soapy water and gave everything a spritz. I don't see any bubbles just yet. I have not removed the clutch and its cover to get a look at that seal. I was just thinking, but for that can i just check to see if any air is coming out of the crankcase breather instead? Or what is the chances that my $15 scamazon blood pressure kit has some sort of internal leak?
If it's pumped up to 300mmhg and still has 250mmhg left after 5 minutes. It's actually passed the test.
Many issues are just the test gear. Might be looking for nothing that matters.
UTC

Ossessionato
1958 Allstate 177VMC, 1962 Allstate, Yamaha Vino 70cc
Joined: UTC
Posts: 3272
Location: Philadelphia
 
Ossessionato
1958 Allstate 177VMC, 1962 Allstate, Yamaha Vino 70cc
Joined: UTC
Posts: 3272
Location: Philadelphia
UTC quote
Jack221 wrote:
If it's pumped up to 300mmhg and still has 250mmhg left after 5 minutes. It's actually passed the test.
Many issues are just the test gear. Might be looking for nothing that matters.
Easy check. Spray the hose connections with soapy water.
OP
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
Jack221 wrote:
If it's pumped up to 300mmhg and still has 250mmhg left after 5 minutes. It's actually passed the test.
Many issues are just the test gear. Might be looking for nothing that matters.
I just did another test and timed it with a watch. It takes 1 hour and 5 minutes for the pressure to drop from 300mmhg to 250. Am i chasing ghosts?
@qascooter avatar
UTC

Veni, Vidi, Posti
79 P200E (Ruby), 62 Allstate (B-62), 63 VBB (Storm)
Joined: UTC
Posts: 5325
Location: Florence, OR
 
Veni, Vidi, Posti
@qascooter avatar
79 P200E (Ruby), 62 Allstate (B-62), 63 VBB (Storm)
Joined: UTC
Posts: 5325
Location: Florence, OR
UTC quote
whodatschrome wrote:
I just did another test and timed it with a watch. It takes 1 hour and 5 minutes for the pressure to drop from 300mmhg to 250. Am i chasing ghosts?
Yes
OP
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
I just drilled the fuel bowl hole out to 2.2mm. And out of all my 24/24 carbs, i don't recall seeing this type of brass fuel outlet on my others. Will there be less fuel flow with theses smaller orifices?
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
@charlieman22 avatar
UTC

Nedminder
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
 
Nedminder
@charlieman22 avatar
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
UTC quote
Should be fine.
Somewhere in my 100 pages - I ram into this.
Think the three hole is modern version of single hole.

But all should have the brass outlet.
If it's missing on other, that would be weird.
@ginch avatar
UTC

Veni, Vidi, Posti
74 Super, 75 Super, PX project, LML off-roader and '66 Blue Badge Smallframe
Joined: UTC
Posts: 10443
Location: Ballarat VIC, Australia
 
Veni, Vidi, Posti
@ginch avatar
74 Super, 75 Super, PX project, LML off-roader and '66 Blue Badge Smallframe
Joined: UTC
Posts: 10443
Location: Ballarat VIC, Australia
UTC quote
charlieman22 wrote:
But all should have the brass outlet.
If it's missing on other, that would be weird.
I think WDC means they're different than the one in the photo. If the spray bar was missing it would not work at all.
OP
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
charlieman22 wrote:
Should be fine.
Somewhere in my 100 pages - I ram into this.
Think the three hole is modern version of single hole.

But all should have the brass outlet.
If it's missing on other, that would be weird.
I just wasn't sure if the three hole version required a different jetting. I did take a quick look see at my pile O 20/20 and 24/24 carbs, and only two of them were the three hole version. Even the 20/20 off of my 2005 Px150 had the single opening in the spray bar.
Forum member supplied image with no explanatory text
@charlieman22 avatar
UTC

Nedminder
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
 
Nedminder
@charlieman22 avatar
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
UTC quote
Gotcha.
Others can probably comment on the newer vs older question.
Best I know - they are all jet-able.

Air tight motor.
Drilled carb.
Will be interested to see how it all goes now.
OP
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
charlieman22 wrote:
Gotcha.
Others can probably comment on the newer vs older question.
Best I know - they are all jet-able.

Air tight motor.
Drilled carb.
Will be interested to see how it all goes now.
I'm curious as well. I'm really looking forwards to a test ride. We've had constant rain for the past 3 days. Temp was in the low 30's today. It was raining slushy snowflakes this afternoon. There might be a short break in the weather this saturday or sunday, but the day time high is supposed to be in the upper 30's.
@ray8 avatar
UTC

Ossessionato
Joined: UTC
Posts: 2429
Location: Los Angeles
 
Ossessionato
@ray8 avatar
Joined: UTC
Posts: 2429
Location: Los Angeles
UTC quote
charlieman22 wrote:
Are T5s un rideable in the city?
I've never heard that.
T5 is a different animal.
@ray8 avatar
UTC

Ossessionato
Joined: UTC
Posts: 2429
Location: Los Angeles
 
Ossessionato
@ray8 avatar
Joined: UTC
Posts: 2429
Location: Los Angeles
UTC quote
whodatschrome wrote:
I just drilled the fuel bowl hole out to 2.2mm. And out of all my 24/24 carbs, i don't recall seeing this type of brass fuel outlet on my others. Will there be less fuel flow with theses smaller orifices?
I have the same on one Spaco. None of the others have those curious holes.
Pretty sure it arrived with a 190/BE4.
OP
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
Is there a specific carb slide that i should be using? Or better yet, are there any slides that i should not be using? I have some random slides on my shelf. I have no idea which ones they are though. The current slide that's in this carb has no cutout on underneath side.
Forum member supplied image with no explanatory text
@charlieman22 avatar
UTC

Nedminder
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
 
Nedminder
@charlieman22 avatar
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
UTC quote
Iirc, they normally have the cut out underneath.
Think it mostly affects the 1/8th throttle - but I could be making that up.
If you have one with the cut out, I'd probably start there.
Perhaps someone else can give u something more definitive.
@ray8 avatar
UTC

Ossessionato
Joined: UTC
Posts: 2429
Location: Los Angeles
 
Ossessionato
@ray8 avatar
Joined: UTC
Posts: 2429
Location: Los Angeles
UTC quote
whodatschrome wrote:
Is there a specific carb slide that i should be using? Or better yet, are there any slides that i should not be using? I have some random slides on my shelf. I have no idea which ones they are though. The current slide that's in this carb has no cutout on underneath side.
That's a G carb slide.
Use one with a cutout. You can always tape over/block the hole that feeds it to simulate a flat slide.
OP
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
Ray8 wrote:
That's a G carb slide.
Use one with a cutout. You can always tape over/block the hole that feeds it to simulate a flat slide.
I woke up this morning to snow so no test ride today. I did swap in a standard E carb slide this morning.
Forum member supplied image with no explanatory text
@chandlerman avatar
UTC

Innovator
63 GL, 62 VBB, 05 Stella, 66 Smallstate, 66 Lammy S3, 63 Lammy S3 Riverside
Joined: UTC
Posts: 13322
Location: Nashville

391 Days Since Last Explosion
 
Innovator
@chandlerman avatar
63 GL, 62 VBB, 05 Stella, 66 Smallstate, 66 Lammy S3, 63 Lammy S3 Riverside
Joined: UTC
Posts: 13322
Location: Nashville

391 Days Since Last Explosion
UTC quote
qascooter wrote:
Yes
+1
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
This is the slide from a stock SI24 24E. It's stamped 8492 4 and it's a Dellorto if that helps. Nice snow by the way.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
OP
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
I have another update, but nothing has really changed much. Here is my current setup-
-24/24E carb drilled to 2.2mm
-AC120/BE3/138MJ
-idle 52/140
-1.5mm squish
-150psi cylinder head compression
-VAPE static ignition set at 21~22
-60mm crank. 125/-5 inlet timing

I did my testing while the scooter was on the centerstand.

Engine still revs really high...close to 10k. I removed the main jet completely from the jet stack and screwed the AC120 and the atomizer back into the carb (with no MJ). I started up the engine and it would only rev up to 7.1k rpm. I still would like to limit to around 8k (while on the centerstand). Anyone got any other pro tips?
OP
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
whodatschrome wrote:
I have another update, but nothing has really changed much. Here is my current setup-
-24/24E carb drilled to 2.2mm
-AC120/BE3/138MJ
-idle 52/140
-1.5mm squish
-150psi cylinder head compression
-VAPE static ignition set at 21~22
-60mm crank. 125/-5 inlet timing

I did my testing while the scooter was on the centerstand.

Engine still revs really high...right around 10k rpm. I removed the main jet completely from the jet stack and screwed the AC120 and the atomizer back into the carb (with no MJ). I started up the engine and it would only rev up to 7.1k rpm. I still would like to limit to around 8k (while on the centerstand). Anyone got any other pro tips?
@charlieman22 avatar
UTC

Nedminder
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
 
Nedminder
@charlieman22 avatar
62 VBB1T Round Tail W/ leaner sidecar
Joined: UTC
Posts: 5009
Location: california
UTC quote
Interesting that it's so thirsty.
Like your test.

The build isn't wildly fuel demanding.
So there's a restriction somewhere.
Two most likely culprits I'd guess:
- The three hole outlet bar.
- Hole in float bowl not large enough.

WWID?
Three things to follow up your test with in order of destruction.
1. Go to 100AC. Not gonna fix volume - but it would help with mix
2. Drill out hole to 2.5 (might have no effect)
3. Cut the outlet bar at an angle and hope the internal channel is larger ID than the pin holes.

Which is to say - I would start with #3.
🙂

I've got a 24/24 somewhere on my shelve you could try if you'd prefer.
Just PM me.
UTC

Jet Eye Master
PX221 MHR heavily tuned, PX200 O tuned, PX181 M1XL tuned, PX166 tuned a quite bit and some motorbikes
Joined: UTC
Posts: 5491
Location: London UK
 
Jet Eye Master
PX221 MHR heavily tuned, PX200 O tuned, PX181 M1XL tuned, PX166 tuned a quite bit and some motorbikes
Joined: UTC
Posts: 5491
Location: London UK
UTC quote
Jack221 wrote:
It'll be fine. Timing is already close to good. Jetting is not quite enough, that's all. Change the AC to 100. I'm guessing after that, you'll need a bigger pilot jet too.
When jetted over rich it won't rev, then adjusting begins.
Back on page 10

Modern Vespa is the premier site for modern Vespa and Piaggio scooters. Vespa GTS300, GTS250, GTV, GT200, LX150, LXS, ET4, ET2, MP3, Fuoco, Elettrica and more.

Modern Vespa is made possible by our generous supporters.

Buy Me A Coffee
 

Shop on Amazon with Modern Vespa

Modern Vespa is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com


All Content Copyright 2005-2026 by Modern Vespa.
All Rights Reserved.


[ Time: 0.0417s ][ Queries: 4 (0.0336s) ][ live ][ 343 ][ ThingOne ]