Forum -> Project Reports
Search Topic
Installing fans in GTS engine bay
OP
@steelbytes avatar
SteelBytes
UTC
Veni, Vidi, Posti
2019 GTS 300 HPE w Malossi cylinder & cam
Joined: UTC
Posts: 8299
Location: Batmania aka Melbourne, Aus
 
SteelBytes
Veni, Vidi, Posti
@steelbytes avatar
2019 GTS 300 HPE w Malossi cylinder & cam
Joined: UTC
Posts: 8299
Location: Batmania aka Melbourne, Aus
UTC quote
EDIT: although early measurements and testing suggested that 60mm was enough, probably should have used 50mm

Two 60x60x25mm computer fans. These are medium speed (3000rpm) but have some high speed (5000rpm) on order.

Fused, currently no switch. Wired to taillight circuit.

The bracket is made from an old computer case. It is stiff due to those "wings" being bent at an angle.

No, the pet carrier does not block them.

Flow direction is towards rear.
Adequate clearance above mudguard to allow full shock compression
Adequate clearance above mudguard to allow full shock compression
Wings 'n bends 'n bolt holes
Wings 'n bends 'n bolt holes
The fans
The fans
View from below. Pet carrier does not block them.
View from below. Pet carrier does not block them.
⚠️ Last edited by SteelBytes on UTC; edited 2 times
@mike_holland avatar
Mike Holland
UTC
Ossessionato
GTS300 Super 2023 Beige
Joined: UTC
Posts: 3490
Location: Sydney, Australia
 
Mike Holland
Ossessionato
@mike_holland avatar
GTS300 Super 2023 Beige
Joined: UTC
Posts: 3490
Location: Sydney, Australia
UTC quote
Why? Is this to protect the ECU from overheating?
⚠️ Last edited by Mike Holland on UTC; edited 1 time
OP
@steelbytes avatar
SteelBytes
UTC
Veni, Vidi, Posti
2019 GTS 300 HPE w Malossi cylinder & cam
Joined: UTC
Posts: 8299
Location: Batmania aka Melbourne, Aus
 
SteelBytes
Veni, Vidi, Posti
@steelbytes avatar
2019 GTS 300 HPE w Malossi cylinder & cam
Joined: UTC
Posts: 8299
Location: Batmania aka Melbourne, Aus
UTC quote
Mike Holland wrote:
Why? Do you want to carry your beer in the pet carrier?
If i did then this might be a good way
Forum member supplied image with no explanatory text
Positive
@mike_holland avatar
Mike Holland
UTC
Ossessionato
GTS300 Super 2023 Beige
Joined: UTC
Posts: 3490
Location: Sydney, Australia
 
Mike Holland
Ossessionato
@mike_holland avatar
GTS300 Super 2023 Beige
Joined: UTC
Posts: 3490
Location: Sydney, Australia
UTC quote
You were too quick, got in before I edited my post.
OP
@steelbytes avatar
SteelBytes
UTC
Veni, Vidi, Posti
2019 GTS 300 HPE w Malossi cylinder & cam
Joined: UTC
Posts: 8299
Location: Batmania aka Melbourne, Aus
 
SteelBytes
Veni, Vidi, Posti
@steelbytes avatar
2019 GTS 300 HPE w Malossi cylinder & cam
Joined: UTC
Posts: 8299
Location: Batmania aka Melbourne, Aus
UTC quote
Mike Holland wrote:
Why? Is this to protect the ECU from overheating?
Part of a multipronged approach
⬆️    About 3 months elapsed    ⬇️
@jess avatar
jess
UTC
Petty Tyrant
0:7 and counting
Joined: UTC
Posts: 39622
Location: Bay Area, California
 
jess
Petty Tyrant
@jess avatar
0:7 and counting
Joined: UTC
Posts: 39622
Location: Bay Area, California
UTC quote
I missed this when you first posted it. And yes, I think this is probably a first.

Can you tell us more about what you're trying to achieve?
Post Reply
Forum -> Project Reports

Modern Vespa is the premier site for modern Vespa and Piaggio scooters. Vespa GTS300, GTS250, GTV, GT200, LX150, LXS, ET4, ET2, MP3, Fuoco, Elettrica and more.

Modern Vespa is made possible by our generous supporters.

Buy Me A Coffee
 
Shop on Amazon with Modern Vespa

Modern Vespa is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com

All Content Copyright 2005-2026 by Modern Vespa.
All Rights Reserved.

[ Time: 0.0140s ][ Queries: 4 (0.0022s) ][ live ][ 339 ][ ThingOne ]