OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
I needed something that could fit in a Cessna 206 that could carry my wife and myself short distances after landing so we didn't have to rent a car or get a ride. Knew nothing of Vespas. Did a little research and a P200E sounded good. A friend overheard me talking and said his dad in the Santa Cruz area had his grandfather's old Vespa and would sell it. Made a call and flew into Watsonville to check it out. Been sitting under a tarp since 1979. The year was 2008 and it looked complete. Made the deal and flew home with it in the plane. Took me awhile to figure out it was a Cushman imported VS5 GS 150. Couldn't find many parts for the engine so decided to install a PX 200 without the starter and oil system. Fixed everything on the frame and got the adapter bracket squared away. Primed it all then painted the wheels and suspension parts like the original color. Was going to paint it white to match my 61 Beetle but never got around to it. After many side jobs building motorcycles for other people it's finally time to finish my scoot! Decided on black cause I have plenty of it and didn't fancy the original color. Underneath two rattle can paint jobs the original wasn't worth keeping. I chose Donatella (as in Versace) because of a classic black paint job and like her modifications with plastic surgery I'm installing a Malossi cased 221 Sport engine. Here's some pics to start.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
⚠️ Last edited by BajaRob on UTC; edited 1 time
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
Gick would you be so kind to give me your advice on if I'm getting close to how the top of the legshield should look? I don't have a reference to work with. Thank you.
Forum member supplied image with no explanatory text
@gickspeed avatar
UTC

Ossessionato
Joined: UTC
Posts: 2850
Location: Racing Capital of the World
 
Ossessionato
@gickspeed avatar
Joined: UTC
Posts: 2850
Location: Racing Capital of the World
UTC quote
BajaRob wrote:
Gick would you be so kind to give me your advice on if I'm getting close to how the top of the legshield should look? I don't have a reference to work with. Thank you.
from the top it looks good. did the tear get welded up? That is paramount.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
GickSpeed wrote:
from the top it looks good. did the tear get welded up? That is paramount.
Yes sir. The tear was on the top right. I still have a slight bend on the right top I need to fix. Thanks!
@gickspeed avatar
UTC

Ossessionato
Joined: UTC
Posts: 2850
Location: Racing Capital of the World
 
Ossessionato
@gickspeed avatar
Joined: UTC
Posts: 2850
Location: Racing Capital of the World
UTC quote
BajaRob wrote:
Yes sir. The tear was on the top right. I still have a slight bend on the right top I need to fix. Thanks!
the tubular legsheild beading will cover a magnitude of sin. i have some original INOX for some of my GS's, others i just bought new. Having ULMA equipment is not going to get you home.
@ray8 avatar
UTC

Ossessionato
Joined: UTC
Posts: 2429
Location: Los Angeles
 
Ossessionato
@ray8 avatar
Joined: UTC
Posts: 2429
Location: Los Angeles
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
Ray8 wrote:
It's already a done deal Ray.🙂 Thank you for that great link! I hope to ride down sometime and buy you a coffee. Someday I'd like to get a small frame too.
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
I think my least favorite job is fitting the outer floor rails.
Forum member supplied image with no explanatory text
@orwell84 avatar
UTC

Ossessionato
Joined: UTC
Posts: 4114
Location: northern New York
 
Ossessionato
@orwell84 avatar
Joined: UTC
Posts: 4114
Location: northern New York
UTC quote
BajaRob wrote:
I think my least favorite job is fitting the outer floor rails.
I love Clecos. Gonna drag out the handful that I haven't managed to melt with the welder yet. Should be enough for the floor rails.

https://www.amazon.com/Fastener-Deluxe-Fasteners-Clamps-Pliers/dp/B08VQBZBBT/ref=mp_s_a_1_1_sspa?keywords=Cleco+Fasteners&qid=1705878237&sr=8-1-spons&ufe=app_do%3Aamzn1.fos.006c50ae-5d4c-4777-9bc0-4513d670b6bc&sp_csd=d2lkZ2V0TmFtZT1zcF9waG9uZV9zZWFyY2hfYXRm&psc=1
@birdsnest avatar
UTC

Not So Moderator
VNB VSC VSX Li150 09C C125 - (vmb vse v9b)
Joined: UTC
Posts: 10904
Location: Hustletown, TX
 
Not So Moderator
@birdsnest avatar
VNB VSC VSX Li150 09C C125 - (vmb vse v9b)
Joined: UTC
Posts: 10904
Location: Hustletown, TX
UTC quote
Cool stuff.

Floor rails... Buy the floor rail tool. I had done maybe 4 or 5 bikes without it. I finally bought one for the ET3 project and immediately hated myself for not having bought it sooner. Time is money and all...
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
Birdsnest wrote:
Cool stuff.

Floor rails... Buy the floor rail tool. I had done maybe 4 or 5 bikes without it. I finally bought one for the ET3 project and immediately hated myself for not having bought it sooner. Time is money and all...
I didn't know there was such a thing!!! I would've definitely bought one. I finished the rails but I'm going to look for that tool, thanks!
@birdsnest avatar
UTC

Not So Moderator
VNB VSC VSX Li150 09C C125 - (vmb vse v9b)
Joined: UTC
Posts: 10904
Location: Hustletown, TX
 
Not So Moderator
@birdsnest avatar
VNB VSC VSX Li150 09C C125 - (vmb vse v9b)
Joined: UTC
Posts: 10904
Location: Hustletown, TX
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
Ah, you're talking about the rivet tool! I'm good in that department. The floor runners themselves where a beast to fit on the frame. They didn't match the curvature of the frame very well. The aluminum in my kit seemed extra hard. Bending up and down is easy but the side to side was difficult without ruining the runner.
@hibbert avatar
UTC

Molto Verboso
Vespa
Joined: UTC
Posts: 1986
Location: California
 
Molto Verboso
@hibbert avatar
Vespa
Joined: UTC
Posts: 1986
Location: California
UTC quote
This scooter should be 'restored' mechanically and cosmetically. There are new aluminum cylinders and other performance items available now. Putting a P200 engine and painting it other than original color is sacrilege.
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
hibbert wrote:
This scooter should be 'restored' mechanically and cosmetically. There are new aluminum cylinders and other performance items available now. Putting a P200 engine and painting it other than original color is sacrilege.
Thank you for your input. I did most of the work in 2009. Besides the paint color the scoot hasn't been altered much. Just a small piece removed on the frame to fit the airbox better. Easily welded back on. I recently discovered new parts for the engine and will eventually get it restored and put back in. I've always been a rider (enjoy long rides and seeing places ) and can't stand trailer queens that only get started at events and not ridden. I totally get what you're saying and everyone has their own opinion and way of doing things. Hope to see you out on the road sometime. I'd like to take a look at yours just as much as I'd like to see everyone else's here on MV. Hope you can live with the choices I've made but if not that's OK too. I welcome all opinions here, that's why I posted my build! Cheers
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
Hibbert I forgot to add one more thing. I believe Donatella was a beautiful woman and didn't need to change her appearance with surgery but she did and that's her prerogative, hence the reason for my choice in names. I don't know her personally but I'm sure she's a wonderful person and is always welcome to come for a ride on my GS. If I restored this scoot into it's original pristine condition I wouldn't want to ride it and that just defeats the whole purpose. Others wouldn't agree and that's fine but this is my scoot. Have a great day.
⚠️ Last edited by BajaRob on UTC; edited 1 time
@hibbert avatar
UTC

Molto Verboso
Vespa
Joined: UTC
Posts: 1986
Location: California
 
Molto Verboso
@hibbert avatar
Vespa
Joined: UTC
Posts: 1986
Location: California
UTC quote
Admittedly I am biased because I have one. There is also a very good feeling when the engine runs good that can't be improved with a P2. Good luck I am rooting for you.
@birdsnest avatar
UTC

Not So Moderator
VNB VSC VSX Li150 09C C125 - (vmb vse v9b)
Joined: UTC
Posts: 10904
Location: Hustletown, TX
 
Not So Moderator
@birdsnest avatar
VNB VSC VSX Li150 09C C125 - (vmb vse v9b)
Joined: UTC
Posts: 10904
Location: Hustletown, TX
UTC quote
^^^
Yeah…
Piston ported Vespas have their own magic.
@ray8 avatar
UTC

Ossessionato
Joined: UTC
Posts: 2429
Location: Los Angeles
 
Ossessionato
@ray8 avatar
Joined: UTC
Posts: 2429
Location: Los Angeles
UTC quote
BajaRob wrote:
but the side to side was difficult without ruining the runner.
Soft jaw vice and gentle persuasion with a wrench.

Have you checked the front fork?
Looks bent, but that could easily be pic distortion.
Level it in a vice to check if not. Upper and lower tubes should be parallel.
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
Ray8 wrote:
Soft jaw vice and gentle persuasion with a wrench.

Have you checked the front fork?
Looks bent, but that could easily be pic distortion.
Level it in a vice to check if not. Upper and lower tubes should be parallel.
The fork definitely looks bent in the pic. It's been so long but I vaguely remember checking it. I'll have to look it over again. Finished the floor rails and only managed to drill into one of my fingers.
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
Started assembling the Malossi cases. All the bearings are in. Only the clutch side crank bearing needed a few taps. Used a shop press to install the engine buffers. They kept trying to go in sideways.🤣 I used a zip tie to compress the edge and they went right in. Next I'll decide on the gearing and seal up the cases.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
UTC

Jet Eye Master
PX221 MHR heavily tuned, PX200 O tuned, PX181 M1XL tuned, PX166 tuned a quite bit and some motorbikes
Joined: UTC
Posts: 5494
Location: London UK
 
Jet Eye Master
PX221 MHR heavily tuned, PX200 O tuned, PX181 M1XL tuned, PX166 tuned a quite bit and some motorbikes
Joined: UTC
Posts: 5494
Location: London UK
UTC quote
I must be really hard, I just push the engine mounts in with my fingers.
Now, some of the Malossi cases are machined too far. SIP make plastic spacers to stop them moving about. If one mount goes fully in and then, the other one pushes the first out again, you need the spacers.
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
Jack221 wrote:
I must be really hard, I just push the engine mounts in with my fingers.
Now, some of the Malossi cases are machined too far. SIP make plastic spacers to stop them moving about. If one mount goes fully in and then, the other one pushes the first out again, you need the spacers.
You're totally right Jack. I just looked inside and sure enough there is some extra space unlike the Piaggio case that has that special washer. The instructions said to just install till 5mm of shaft is exposed. That's lame. Thanks for the tip!
UTC

Jet Eye Master
PX221 MHR heavily tuned, PX200 O tuned, PX181 M1XL tuned, PX166 tuned a quite bit and some motorbikes
Joined: UTC
Posts: 5494
Location: London UK
 
Jet Eye Master
PX221 MHR heavily tuned, PX200 O tuned, PX181 M1XL tuned, PX166 tuned a quite bit and some motorbikes
Joined: UTC
Posts: 5494
Location: London UK
UTC quote
BajaRob wrote:
You're totally right Jack. I just looked inside and sure enough there is some extra space unlike the Piaggio case that has that special washer. The instructions said to just install till 5mm of shaft is exposed. That's lame. Thanks for the tip!
https://www.sip-scootershop.com/en/product/spacer-set-rubber-engine-mount-malossi-engine-case-left-right-2-radscheune_17453910

It's not all casings but without these they slide about. Considering scooters with these casings are probably quite fast, it's not optimum safety from Malossi.
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
Thanks to you crafty buggers here on NSM I put together my leak tester this morning. Just waiting for some parts from SIP so I can finish assembling my engine.
Forum member supplied image with no explanatory text
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
Built the battery box out of some stainless I had laying around. Parts for my engine showed up last night. Hopefully I'll get some progress done on that.
Forum member supplied image with no explanatory text
@leif avatar
UTC

Member
1955 Acma, 1958 and 59 GS150. PXs
Joined: UTC
Posts: 33
Location: Germany
 
Member
@leif avatar
1955 Acma, 1958 and 59 GS150. PXs
Joined: UTC
Posts: 33
Location: Germany
UTC quote
Hi,
Why do you need a battery?
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
Leif wrote:
Hi,
Why do you need a battery?
Well my original thought was to just run the vape ignition AC and no battery. My stock battery tray was corroded so bad it crumbled off so I thought why not leave it off and have more storage in there. I had Speedo King restore the original speedo and it turned out beautiful. He did it probably in 2009. I recently started work on the scoot again and discovered the SIP speedo. After reading posts about that speedo going off and on at idle I decided to go DC with the little battery. That would have driven me nuts.
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
BajaRob wrote:
Built the battery box out of some stainless I had laying around. Parts for my engine showed up last night. Hopefully I'll get some progress done on that.
Nice work on the battery box. It looks VERY sanitary. I'd love to see more pics of it at different angles.
@leif avatar
UTC

Member
1955 Acma, 1958 and 59 GS150. PXs
Joined: UTC
Posts: 33
Location: Germany
 
Member
@leif avatar
1955 Acma, 1958 and 59 GS150. PXs
Joined: UTC
Posts: 33
Location: Germany
UTC quote
BajaRob wrote:
Well my original thought was to just run the vape ignition AC and no battery. My stock battery tray was corroded so bad it crumbled off so I thought why not leave it off and have more storage in there. I had Speedo King restore the original speedo and it turned out beautiful. He did it probably in 2009. I recently started work on the scoot again and discovered the SIP speedo. After reading posts about that speedo going off and on at idle I decided to go DC with the little battery. That would have driven me nuts.
Ok, understandable. I got rid of my battery on my VS5 and put in a Flytech ignition. Unfortunately, that one is really weak when it comes to the lighting.
As most of the ignition stuff on my VS4 is missing, I have bought a Vape already. I like not having a battery, as I am doing a lot of rallies and the GS must carry a lot of oil (6% mix), fuel and tools under the cowl.
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
whodatschrome wrote:
Nice work on the battery box. It looks VERY sanitary. I'd love to see more pics of it at different angles.
Here you go. Cut the head off a stainless bolt and welded it from the back. Foam on the bottom. I left a little space between battery and frame for another foam strip. Have space on bottom of box for drainage (hopefully won't need to make any river crossings). I liked your fuse holder but haven't got that far yet. Think I'll leave the natural finish. Might polish it a little.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
Had some bad kickstart quadrant rubber stops so couldn't close the case halves yet. I did manage to remove the Malossi engine buffers and installed the plastic spacers and a new set of buffers. Didn't know if the original ones would survive extraction.
Need some recommendations on squish for the 221. Freak Moped has a video and said to use a standard cylinder base gasket and a 2mm head packer and call it good. My cylinder kit came with 1 copper .12, silver .20 and another silver gasket at .30. I've measured the squish on the head and cylinder with no base gasket. Just need to know what the head total squish should be so I can put the right base gasket on. I'm using the vape road ignition and a Pinasco VRX-R 26 carb. Any thoughts on that carb, with or without venturi and jetting setup would be greatly appreciated.
I hit the gas tank with some 2500 and did some buffing with my mini pneumatic buffer. The rear of the tank is final buffed and the forward or top part just needs the final foam pad to remove the light swirl marks for comparison. I also pulled out a wheel I painted to see how close it matched the Scootopia drum I bought. Close enough for me.
Forum member supplied image with no explanatory text
Forum member supplied image with no explanatory text
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
BajaRob wrote:
Had some bad kickstart quadrant rubber stops so couldn't close the case halves yet. I did manage to remove the Malossi engine buffers and installed the plastic spacers and a new set of buffers. Didn't know if the original ones would survive extraction.
Need some recommendations on squish for the 221. Freak Moped has a video and said to use a standard cylinder base gasket and a 2mm head packer and call it good. My cylinder kit came with 1 copper .12, silver .20 and another silver gasket at .30. I've measured the squish on the head and cylinder with no base gasket. Just need to know what the head total squish should be so I can put the right base gasket on. I'm using the vape road ignition and a Pinasco VRX-R 26 carb. Any thoughts on that carb, with or without venturi and jetting setup would be greatly appreciated.
I hit the gas tank with some 2500 and did some buffing with my mini pneumatic buffer. The rear of the tank is final buffed and the forward or top part just needs the final foam pad to remove the light swirl marks for comparison. I also pulled out a wheel I painted to see how close it matched the Scootopia drum I bought. Close enough for me.
Ooooo....that's a shiny tank! The wheel and hub also look really sharp.

For a road going touring engine i've always aimed for around a 1.4~1.5mm squish. If you're looking to eek out more power, then i'd shoot for less...maybe somewhere around 1.2mm? I know some builders narrow it up to around 1mm. It all depends upon how you primarily plan to use this scooter for, and i think you're planning on some 2up riding?
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
Thank you sir!
I'm sure you already knew I'm using the Malossi V1 case and the newer 210 Sport kit and head. I don't want to go crazy squeezing everything out of the engine. I want it to be reliable for long rides. I've decided the wife will be better off riding on the P. She'll scratch the shit out of the cowls with her pants and shoes!😂 She's also uneasy riding without some back support(always thinks about falling off the back). I'm going to try a short 4th and 24 tooth on the clutch. I can always put the 23 in. I have hills to climb out here too so at least I have options. Right now squish without base gasket is 1.26mm. The copper gasket is .12 and the thin silver is .20. Looks like I'm right in there. Going to try 18° for the timing. The airbox is my only hang up fitting wise in the frame. If I can't get an SI to work a round slide carb should.

I'm trying to go hard core on the paint job since I've given advice about painting. Hopefully when people see it fingers won't be pointed with ensuing laughter. [ lowers head and pushes scooter out of view ].🤣😂 I'll try not to rush it!
UTC

parallelogramerist
Joined: UTC
Posts: 6283
 
parallelogramerist
Joined: UTC
Posts: 6283
UTC quote
BajaRob wrote:
Thank you sir!
I'm sure you already knew I'm using the Malossi V1 case and the newer 210 Sport kit and head. I don't want to go crazy squeezing everything out of the engine. I want it to be reliable for long rides. I've decided the wife will be better off riding on the P. She'll scratch the shit out of the cowls with her pants and shoes!😂 She's also uneasy riding without some back support(always thinks about falling off the back). I'm going to try a short 4th and 24 tooth on the clutch. I can always put the 23 in. I have hills to climb out here too so at least I have options. Right now squish without base gasket is 1.26mm. The copper gasket is .12 and the thin silver is .20. Looks like I'm right in there. Going to try 18° for the timing. The airbox is my only hang up fitting wise in the frame. If I can't get an SI to work a round slide carb should.

I'm trying to go hard core on the paint job since I've given advice about painting. Hopefully when people see it fingers won't be pointed with ensuing laughter. [ lowers head and pushes scooter out of view ].🤣😂 I'll try not to rush it!
A largeframe airbox will definitely be a challenge to fit. I've heard that sometimes part of the frame can simply be bent out of the way. Other times part of the frame gets cut and removed. I've also seen the upper portion of the carb box cut away, yet still utilize the stock air filter. Lots of it depends upon the offset of the largeframe engine adapter bracket. I don't know if any of the adapter brackets allow the rear shock's upper and lower mounting locations to actually line up with each other. The second part to that, does the engine adapter line up the rear wheel with the wheel on the front fork? I went (suffered?) though all of that with my rusty VB1 build a few years ago. What i did find out what that a smallblock 150 engine will physically fit much easier than a 200 block.
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
You're right on whodat. I want to do the least amount of change to the frame as possible. I bought an adapter years ago and it had the engine moved far to the right. I cut it up and lined both tires up with the rear in the center of the frame. I got an adapter fitting inside the upper shock mount for the different thread pitch. I did cut out a little piece of the frame, easy to replace. I started to modify the P200 carb box and think a custom fabbed top might work out. I definitely want a filter of some sort. Probably will be a pod type mounted off the box. I bought a cheap PHB style carb with manifold and found it will work if I cut and redirect the manifold. I'll go that route if the SI carb doesn't comply. Parts showing up today so I can finish the engine and and get moving on the carb challenge. I'll definitely need to bust out some WDCI to get through this! (In layman's terms, whodatschrome ingenuity)
@roland87 avatar
UTC

Molto Verboso
'13 LML Star 200, '81 50 Special, '81 P 150 X, '89 PK 50 Nuova, '84 PK 50 S, '82 PK 50 S
Joined: UTC
Posts: 1866
Location: Ukraine. Kyiv.
 
Molto Verboso
@roland87 avatar
'13 LML Star 200, '81 50 Special, '81 P 150 X, '89 PK 50 Nuova, '84 PK 50 S, '82 PK 50 S
Joined: UTC
Posts: 1866
Location: Ukraine. Kyiv.
UTC quote
Awesome job
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
Thanks Roland! I hope it looks as nice as yours!
@gickspeed avatar
UTC

Ossessionato
Joined: UTC
Posts: 2850
Location: Racing Capital of the World
 
Ossessionato
@gickspeed avatar
Joined: UTC
Posts: 2850
Location: Racing Capital of the World
UTC quote
Airbox fits a-okay.
Forum member supplied image with no explanatory text
OP
@bajarob avatar
UTC

Ossessionato
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
 
Ossessionato
@bajarob avatar
1961 VS5T, 1981 P200E, 2003 Malaguti F12 Phantom,Rigid Frame Chopper, 2001 Harley FXDXT
Joined: UTC
Posts: 2214
Location: Ventura, CA
UTC quote
GickSpeed wrote:
Airbox fits a-okay.
Why do you have to tease me with a killer photo like that?! That shot should be in a calendar. An all GS calendar. 😉

Modern Vespa is the premier site for modern Vespa and Piaggio scooters. Vespa GTS300, GTS250, GTV, GT200, LX150, LXS, ET4, ET2, MP3, Fuoco, Elettrica and more.

Modern Vespa is made possible by our generous supporters.

Buy Me A Coffee
 

Shop on Amazon with Modern Vespa

Modern Vespa is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com


All Content Copyright 2005-2026 by Modern Vespa.
All Rights Reserved.


[ Time: 0.0119s ][ Queries: 4 (0.0039s) ][ live ][ 343 ][ ThingOne ]