Thu Nov 09, 2006 11:22 am

El Macho
KTM Super Duke 1290, Vespa GTS 300
Joined: 27 Oct 2006
Posts: 9022
Location: Belfast Metropolitan Area
 
El Macho
KTM Super Duke 1290, Vespa GTS 300
Joined: 27 Oct 2006
Posts: 9022
Location: Belfast Metropolitan Area
Thu Nov 09, 2006 11:22 am linkquote
This is how to install leds into your top box.

First of all take off the lenses with a Philips screwdriver from behind. Make a template using some sort of masking tape. The measurements I used were 19mm between vertical LEDs and 10 mm between the two uprights. Mark dots on the tape. Stick the tape in the appropriate place avoiding the contours and screw hole.


Next, use a very small pilot drill to make small holes or indentations through your template.



Then widen the pilot holes using a 5mm drill.



Push the LEDs in from behind.



and it will look like this from the front:



Now, MOST importantly remove the LEDS and replace the lens as there is not enough room behind the lens to have the LEDs protruding. Once you have replaced the lens, superglue the LEDs in place. I have used 5mm 12v superbright LEDs with 180mcd luminescence. It makes sense to check the LEDs across a nine volt battery before glueing them in place.





When you glue the LEDs in place make sure that you have the cathode which is the shorter terminal on the LED in the centre of both rows as LEDs are current flow dependent and this makes it easier to wire. You can just see if you look very carefully that one terminal is longer than the other:



Next, bend the shorter terminals (cathodes) and the anodes outwards and loop and connect all the anodes together and all the cathodes together like this:



You can clearly follow the centre wire making contact with all the cathodes and the loop wire round the outside tied around the anodes.

You now want to solder the wire rail to the LED terminals and connect both LED sides to a supply wire. Make sure you connect the anodes on one side to the anodes on the other.





Carefully tape the soldered connections down using duck tape as shown here:



Now all there is left to do is to drill a hole in an appropriate place in the base of the top box and connect the wires to your brake light supply. The finished powered up item looks like this.





Last edited by DougL on Sun Sep 06, 2009 12:21 am; edited 1 time in total
Thu Nov 09, 2006 12:33 pm

Addicted
Joined: 06 Sep 2006
Posts: 534
Location: Raleigh, NC, USA
 
Addicted
Joined: 06 Sep 2006
Posts: 534
Location: Raleigh, NC, USA
Thu Nov 09, 2006 12:33 pm linkquote
That looks great! Are they going to be always-on, or are you going to link them with the brake lights?

Does the duct tape really match the inside of the case that well? Or is that a trick of the lighting?
Thu Nov 09, 2006 1:05 pm

Addicted
gt200
Joined: 25 Oct 2005
Posts: 715
Location: NYC
 
Addicted
gt200
Joined: 25 Oct 2005
Posts: 715
Location: NYC
Thu Nov 09, 2006 1:05 pm linkquote
Man that is pimp!!! Very, very cool. And very well organized. You've got to make a little mov when your done, kind of like Jess did.

X
Thu Nov 09, 2006 1:11 pm

El Macho
KTM Super Duke 1290, Vespa GTS 300
Joined: 27 Oct 2006
Posts: 9022
Location: Belfast Metropolitan Area
 
El Macho
KTM Super Duke 1290, Vespa GTS 300
Joined: 27 Oct 2006
Posts: 9022
Location: Belfast Metropolitan Area
Thu Nov 09, 2006 1:11 pm linkquote
CatMoran wrote:
That looks great! Are they going to be always-on, or are you going to link them with the brake lights?

Does the duct tape really match the inside of the case that well? Or is that a trick of the lighting?
Will be linked with the brake lights. The duck tape really does match the inside of the case that well!

Jess... how about a sticky?
Thu Nov 09, 2006 2:04 pm

Hooked
GTS 250ie
Joined: 04 Oct 2006
Posts: 180

 
Hooked
GTS 250ie
Joined: 04 Oct 2006
Posts: 180

Thu Nov 09, 2006 2:04 pm linkquote
Looks really great!
I assume it would work on the GTS top box as well.
One question: Will the superglue seal well enough to keep water out, or does the lens do that?

Bill
Thu Nov 09, 2006 2:17 pm

Petty Tyrant
0:7
Joined: 11 Oct 2005
Posts: 32464
Location: Bay Area, California
 
Petty Tyrant
0:7
Joined: 11 Oct 2005
Posts: 32464
Location: Bay Area, California
Thu Nov 09, 2006 2:17 pm linkquote
dougl65 wrote:
Jess... how about a sticky?
I can put it in the Project Reports area for you...
Thu Nov 09, 2006 2:38 pm

Ossessionato
None! I sold it :(
Joined: 01 Nov 2005
Posts: 3247
Location: Burlington NC
 
Ossessionato
None! I sold it :(
Joined: 01 Nov 2005
Posts: 3247
Location: Burlington NC
Thu Nov 09, 2006 2:38 pm linkquote
Very nice job! Looks killa, Beale.
Thu Nov 09, 2006 3:16 pm

Ossessionato
Piaggio BV 250
Joined: 01 Jul 2006
Posts: 2348
Location: Alameda, CA
 
Ossessionato
Piaggio BV 250
Joined: 01 Jul 2006
Posts: 2348
Location: Alameda, CA
Thu Nov 09, 2006 3:16 pm linkquote
Well thought out and well documented!

Bravo!!
Thu Nov 09, 2006 3:18 pm

El Macho
KTM Super Duke 1290, Vespa GTS 300
Joined: 27 Oct 2006
Posts: 9022
Location: Belfast Metropolitan Area
 
El Macho
KTM Super Duke 1290, Vespa GTS 300
Joined: 27 Oct 2006
Posts: 9022
Location: Belfast Metropolitan Area
Thu Nov 09, 2006 3:18 pm linkquote
jess wrote:
dougl65 wrote:
Jess... how about a sticky?
I can put it in the Project Reports area for you...
Thanks Jess, that would be good...

And thanks for all your comments!

I'll try and get a movie of it flashing with the comagination brake flasher!

If it leaks because the superglue doesn't create a tight enough seal, then out will come some clear silicone. I doubt much water will get in the lens offers quite a bit of protection.
Thu Nov 16, 2006 2:28 pm

Member
Joined: 16 Nov 2006
Posts: 25
Location: Where Everything's Bigger
 
Member
Joined: 16 Nov 2006
Posts: 25
Location: Where Everything's Bigger
Thu Nov 16, 2006 2:28 pm linkquote
Thumbs up mate!
Sat Nov 25, 2006 6:55 pm

Addicted
White Gts 300
Joined: 22 Nov 2006
Posts: 692
Location: Nivelles (Belgium)
 
Addicted
White Gts 300
Joined: 22 Nov 2006
Posts: 692
Location: Nivelles (Belgium)
Sat Nov 25, 2006 6:55 pm linkquote
Super nice job!!!
Maybe one day on mine... 8)

Can you tell us (picture?) what does it look like in daylight?

Thanks!
  DoubleGood Vespa Design  

All Content Copyright 2005-2021 by Modern Vespa. All Rights Reserved.

Modern Vespa is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com.

Shop on Amazon Smile with Modern Vespa

[ Time: 0.0337s ][ Queries: 6 (0.0143s) ][ Debug on ][ 209 ][ Thing One ]